NIV Full Face Mask (CPAP)

Irrigation Set

Item Code

2058

Features :

> It is made from non toxic PVC utilizing soft flexible chamber delivering high flow rates
> Sharp and easy piecing spike
> Smooth roller clamp facilitates easy and controlled adjustment of fluid
> Luer lock at distal end
> To be connected with this spike to a sterile irrigation solution bag
> End of device provide with a connector to connect with bladder catheter

Available Configuration :

Available with soft chamber and hard chamber
Available in single & multi flow double spike

Initial Puncture Needles

3 Part Bevel Tip

OEM manufacture according to your specifications and in your specified material

Available Sizes: 18G x 20cm

3 Part Trocar Tip

OEM manufacture according to your specifications and in your specified material

Available Sizes: 18G x 15cm, 18G x 23cm

3 Part Bevel Tip

OEM manufacture according to your specifications and in your specified material

Available Sizes: 18G x 20cm

3 Part Trocar Tip

OEM manufacture according to your specifications and in your specified material

Available Sizes: 18G x 15cm, 18G x 23cm

Introducer Needles

Y Introducer Needle

Uses highest tensile 304 stainless steel available
Lubricated OR Non-Lubricated
Dimpled echogenic, basted echogenic or non-echogenic

Available Sizes :

18G X 70 mm

Y Introducer Needle

Uses highest tensile 304 stainless steel available
Lubricated OR Non-Lubricated
Dimpled echogenic, basted echogenic or non-echogenic

Available Sizes :

18G X 70 mm

Seldinger Introducer Needle

Uses highest tensile 304 stainless steel available
Lubricated or non-lubricated
Dimpled echogenic, basted echogenic or non-echogenic
Widest array of plastic hub styles available

Available Sizes :

17G to 20G
Length 25 mm to 150 mm

Seldinger Introducer Needle

Uses highest tensile 304 stainless steel available
Lubricated or non-lubricated
Dimpled echogenic, basted echogenic or non-echogenic
Widest array of plastic hub styles available

Available Sizes :

17G to 20G
Length 25 mm to 150 mm

Vertebroplasty Needle

The tip thanks to the appropriate cutting edge,is always able to reach the affected areas.
The thin structure with high quality cannula ensures the maximization of the lumen for cement passage by reducing the resistance also in high viscosity cements

Available Sizes :

11G * 100mm 11G * 150mm
13G * 100mm 13G * 150mm
15G * 100mm 15G * 150mm

OEM manufacture according to your specifications and in your specified material

Vertebroplasty Needle

The tip thanks to the appropriate cutting edge,is always able to reach the affected areas.
The thin structure with high quality cannula ensures the maximization of the lumen for cement passage by reducing the resistance also in high viscosity cements

Available Sizes :

11G * 100mm 11G * 150mm
13G * 100mm 13G * 150mm
15G * 100mm 15G * 150mm

OEM manufacture according to your specifications and in your specified material

Metal hub NRFit Spinal Needle

Longer than Luer connector.
20% smaller commector diameter.
Collared Slip syringes.

Available Sizes :

18G x 90 mm to 27G x 90 mm

OEM manufacture according to your specifications and in your specified material

Metal hub NRFit Spinal Needle

Longer than Luer connector.
20% smaller commector diameter.
Collared Slip syringes.

Available Sizes :

18G x 90 mm to 27G x 90 mm

OEM manufacture according to your specifications and in your specified material

Epidural Needle

OEM manufacture according to your specifications and in your specified material

Ensures unscathed catheter advancement and retraction.
Uses highest tensile 304 stainless steel available.
Available with CM depth marking.

Available Sizes :

14 GA x 80 mm 90 mm, 100 mm
16 GA x 80 mm 90 mm, 100 mm
16 GA x 80 mm 90 mm, 100 mm
18 GA x 80 mm 90 mm, 100 mm

Epidural Needle

OEM manufacture according to your specifications and in your specified material

Ensures unscathed catheter advancement and retraction.
Uses highest tensile 304 stainless steel available.
Available with CM depth marking.

Available Sizes :

14 GA x 80 mm 90 mm, 100 mm
16 GA x 80 mm 90 mm, 100 mm
16 GA x 80 mm 90 mm, 100 mm
18 GA x 80 mm 90 mm, 100 mm

Huber Needle

Uses highest tensile 304 stainless steel available
Straight or bent
Colour-coded plastic hubs

Available Sizes :

18 GA to 24 GA
Length 12 mm to 55 mm

Huber Needle

Uses highest tensile 304 stainless steel available
Straight or bent
Colour-coded plastic hubs

Available Sizes :

18 GA to 24 GA
Length 12 mm to 55 mm

Bone Marrow Aspiration Needles

Luer lock connector on the handle forsecure syringe attachment.

An adjustable, removable needle stop safely controls depth of penetration.

Available Sizes :

13 G x 50 mm / 75 mm / 100 mm
14 G x 50 mm / 75 mm / 100 mm
15 G x 50 mm / 75 mm / 100 mm
16 G x 50 mm / 75 mm / 100 mm
18 G x 50 mm / 75 mm / 100 mm

Bone Marrow Aspiration Needles

Luer lock connector on the handle forsecure syringe attachment.

An adjustable, removable needle stop safely controls depth of penetration.

Available Sizes :

13 G x 50 mm / 75 mm / 100 mm
14 G x 50 mm / 75 mm / 100 mm
15 G x 50 mm / 75 mm / 100 mm
16 G x 50 mm / 75 mm / 100 mm
18 G x 50 mm / 75 mm / 100 mm

R F Needle

OEM Manufacture according to your specification and in your specified material.

Features :

Uses highest tensile 304 stainless steel available.
Customizable gauges, lengths and active tip lengths.

Straight, curved, or sharp tips.
Lubricated or non-lubricated.
Available in quincke bevel.

Gauge	Curved / Straight	Tip Length	Product Length
20	Curved	10MM	100MM
22	Straight	5MM	100MM
22	Straight	10MM	100MM
20	Straight	10MM	100MM
22	Curved	10MM	100MM
20	Straight	5MM	150MM
20	Straight	10MM	150MM
20	Curved	5MM	100MM
20	Curved	10MM	150MM

R F Needle

OEM Manufacture according to your specification and in your specified material.

Features :

Uses highest tensile 304 stainless steel available.
Customizable gauges, lengths and active tip lengths.

Straight, curved, or sharp tips.
Lubricated or non-lubricated.
Available in quincke bevel.

Gauge	Curved / Straight	Tip Length	Product Length
20	Curved	10MM	100MM
22	Straight	5MM	100MM
22	Straight	10MM	100MM
20	Straight	10MM	100MM
22	Curved	10MM	100MM
20	Straight	5MM	150MM
20	Straight	10MM	150MM
20	Curved	5MM	100MM
20	Curved	10MM	150MM

Needle / Syringe Connector

OEM Manufacture according to your specification and in your specified material.

Features :

3.50MM X 2.50MM X 76MM.
3.50MM X 2.50MM X 102MM.
3.50MM X 2.50MM X 127MM.

Needle / Syringe Connector

OEM Manufacture according to your specification and in your specified material.

Features :

3.50MM X 2.50MM X 76MM.
3.50MM X 2.50MM X 102MM.
3.50MM X 2.50MM X 127MM.

Menghini Biopsy Set

OEM Manufacture according to your specification and in your specified material.

Features :

Available Sizes :1.9MM X 110MM
The needle is provided with a sharpened Luer-lock to offer an added safety attachment to the syringe without vacuum loss.

The device is provided with internal stylet with the following functions:

To facilitate the device penetration without skin incision
To avoid the tissue penetration into the lumen of the cannula before reaching the target.
To gradually transmit the created vacuum from the syringe, on the needle tip (thanks to a special processing present on the surface of the stylet).
To avoid the sample aspiration into the cylinder of the syringe, keeping the sample into the cannula and to facilitate the expulsion step.

Menghini Biopsy Set

OEM Manufacture according to your specification and in your specified material.

Features :

Available Sizes :1.9MM X 110MM
The needle is provided with a sharpened Luer-lock to offer an added safety attachment to the syringe without vacuum loss.

The device is provided with internal stylet with the following functions:

To facilitate the device penetration without skin incision
To avoid the tissue penetration into the lumen of the cannula before reaching the target.
To gradually transmit the created vacuum from the syringe, on the needle tip (thanks to a special processing present on the surface of the stylet).
To avoid the sample aspiration into the cylinder of the syringe, keeping the sample into the cannula and to facilitate the expulsion step.

Jamshedi Bone Marrow

OEM Manufacture according to your specification and in your specified material.

Features :

Lightweight handle with built-in comfort knob enables the practitioner to apply sufficient pressure without discomfort.
Tapered distal tip facilitates the recovery of bone marrow samples with unaltered architecture
Single-use design helps assure sterility for every procedure and helps prevent cross contamination.
Razor-sharp bevel tip allows easy coring of the bone.

Gauges	LENGTH(MM)
8G	100 / 150
11G	100 / 150
13G	100 / 150

Jamshedi Bone Marrow

OEM Manufacture according to your specification and in your specified material.

Features :

Lightweight handle with built-in comfort knob enables the practitioner to apply sufficient pressure without discomfort.
Tapered distal tip facilitates the recovery of bone marrow samples with unaltered architecture
Single-use design helps assure sterility for every procedure and helps prevent cross contamination.
Razor-sharp bevel tip allows easy coring of the bone.

Gauges	LENGTH(MM)
8G	100 / 150
11G	100 / 150
13G	100 / 150

Manual Biopsy Needles

OEM Manufacture according to your specification and in your specified material.

Diamter (Available sizes)	Length (cm) (Available sizes)
14G	11.25cm, 15cm
16G	11.25cm, 15cm
18G	11.25cm, 15cm

Manual Biopsy Needles

OEM Manufacture according to your specification and in your specified material.

Diamter (Available sizes)	Length (cm) (Available sizes)
14G	11.25cm, 15cm
16G	11.25cm, 15cm
18G	11.25cm, 15cm

Abrams Pleural Biopsy Needle

OEM Manufacture according to your specification and in your specified material.

Available Sizes : 8G x 3 1/2″ (4mm x 89mm)

Abrams Pleural Biopsy Needle

OEM Manufacture according to your specification and in your specified material.

Available Sizes : 8G x 3 1/2″ (4mm x 89mm)

Bone Marrow Biopsy System

OEM Manufacture according to your specification and in your specified material.

Gauge	Color	Length (MM)	Length (MM)
8	Dark Green	08 100	08 150
9	Pink	09 100	09 150
11	White	11 100	11 150
13	Light Blue	13 100	13 150

Bone Marrow Biopsy System

OEM Manufacture according to your specification and in your specified material.

Gauge	Color	Length (MM)	Length (MM)
8	Dark Green	08 100	08 150
9	Pink	09 100	09 150
11	White	11 100	11 150
13	Light Blue	13 100	13 150

Soft-Core Disposable Biopsy Instrument

Biopsy instrument with or without guiding cannula

OEM Manufacture according to your specification and in your specified material.

Available Sizes :

14Ga – 19,16cm
16Ga – 10,16cm
18Ga – 10,16,20,25*cm

Soft-Core Disposable Biopsy Instrument

Biopsy instrument with or without guiding cannula

OEM Manufacture according to your specification and in your specified material.

Available Sizes :

14Ga – 19,16cm
16Ga – 10,16cm
18Ga – 10,16,20,25*cm

Bendable Trocars:

OEM manufacture according to your specifications and in your specified material

Available Sizes :

4.00mm x 150mm
4.50mm x 150mm
5.40mm x 150mm
6.50mm x 150mm
8.00mm x 150mm

Bendable Trocars:

OEM manufacture according to your specifications and in your specified material

Available Sizes :

4.00mm x 150mm
4.50mm x 150mm
5.40mm x 150mm
6.50mm x 150mm
8.00mm x 150mm

Suture Needles

Available sizes : 14G x 150mm EO Sterile Point
Accommodates any suture
Single Use
OEM Manufacture according to your specifications and in your specified material

Available sizes : 14G x 150mm EO Sterile Point
Accommodates any suture
Single Use
OEM Manufacture according to your specifications and in your specified material

Lumen Needles

OEM manufacture according to your specifications and in your specified material

Single Lumen Tip (Available sizes)	Double Lumen Tip (Available sizes)
1.20mm x 365mm	-
1.40mm x 365mm	1.60mm x 420mm
1.50mm x 365mm	1.50mm x 420mm
1.60mm x 365mm	-

Lumen Needles

OEM manufacture according to your specifications and in your specified material

Single Lumen Tip (Available sizes)	Double Lumen Tip (Available sizes)
1.20mm x 365mm	-
1.40mm x 365mm	1.60mm x 420mm
1.50mm x 365mm	1.50mm x 420mm
1.60mm x 365mm	-

Blood Bag Cannulas

Available Sizes : 16G x 46mm / 54mm
Japanese tubing fistula finish
Smooth finish both inside and outside with burr free ends

Available Sizes : 16G x 46mm / 54mm
Japanese tubing fistula finish
Smooth finish both inside and outside with burr free ends

Back Cut Cannulas

Gauges	Diameter	Length
16G	1.65 mm	83 mm
17G	1.47 mm	83 mm / 86 mm
18G	1.25 mm	83 mm / 86 mm
20G	0.90 mm	83 mm / 86 mm
22G	0.70 mm	70 mm / 73 mm
24G	0.55 mm	62 mm / 65 mm
26G	0.45 mm	52 mm / 55 mm
27G	0.40 mm	52 mm / 55 mm

Back Cut Cannulas

Gauges	Diameter	Length
16G	1.65 mm	83 mm
17G	1.47 mm	83 mm / 86 mm
18G	1.25 mm	83 mm / 86 mm
20G	0.90 mm	83 mm / 86 mm
22G	0.70 mm	70 mm / 73 mm
24G	0.55 mm	62 mm / 65 mm
26G	0.45 mm	52 mm / 55 mm
27G	0.40 mm	52 mm / 55 mm

Chiba Needles

OEM manufacture according to your specifications and in your specified material

Gauges	Length
18G	200 mm
22G	200 mm

Chiba Needles

OEM manufacture according to your specifications and in your specified material

Gauges	Length
18G	200 mm
22G	200 mm

Liver Biopsy Needles

OEM manufacture according to your specifications and in your specified material

Gauges	Length
16G	3 ½"
17G	3 ½"
18G	3 ½"

Liver Biopsy Needles

OEM manufacture according to your specifications and in your specified material

Gauges	Length
16G	3 ½"
17G	3 ½"
18G	3 ½"

Verres Needles

OEM manufacture according to your specifications and in your specified material

Gauges	Diameter	Length
14G	2.10 mm	128 mm / 158 mm
16G	1.65 mm	143.5 mm / 173.5 mm

Verres Needles

OEM manufacture according to your specifications and in your specified material

Gauges	Diameter	Length
14G	2.10 mm	128 mm / 158 mm
16G	1.65 mm	143.5 mm / 173.5 mm

Biopsy Needles

OEM manufacture according to your specifications and in your specified material

Available Sizes :

14G, 16G & 18G
Cannula 105mm x Stylet 170mm
Cannula 145mm x Stylet 210mm
Cannula 180mm x Stylet 245mm

Biopsy Needles

OEM manufacture according to your specifications and in your specified material

Available Sizes :

14G, 16G & 18G
Cannula 105mm x Stylet 170mm
Cannula 145mm x Stylet 210mm
Cannula 180mm x Stylet 245mm

Vertebroplasty Needle

OEM manufacture according to your specifications and in your specified material

Diameter	Length
3.00 mm	100 mm
3.00 mm	125 mm
3.00 mm	150 mm
2.50 mm	125 mm

Vertebroplasty Needle

OEM manufacture according to your specifications and in your specified material

Diameter	Length
3.00 mm	100 mm
3.00 mm	125 mm
3.00 mm	150 mm
2.50 mm	125 mm

Probes

OEM manufacture according to your specifications and in your specified material

Diameter	Length	Hole Diameter	No. of Holes
4.60 mm	340 mm	1.50 mm	8
5.00 mm	340 mm	1.50 mm	12
10.00 mm	340 mm	1.00 / 1.50 mm	32

Probes

OEM manufacture according to your specifications and in your specified material

Diameter	Length	Hole Diameter	No. of Holes
4.60 mm	340 mm	1.50 mm	8
5.00 mm	340 mm	1.50 mm	12
10.00 mm	340 mm	1.00 / 1.50 mm	32

Lipo Suction

Tips	Diameter (mm)	Length (cm)
Toomey Infiltrator	3.0, 3.7	15, 25, 35
Cobra Bi-Bevel	2.1, 2.7, 3.0, 3.7, 4.6	15, 25, 35, 40, 45
Mercedes	2.7, 3.0, 3.7, 4.6	15, 25, 35, 40, 45
Pyramid	2.1, 2.7, 3.0, 3.7, 4.6	15, 25, 35, 40, 45
Standard	2.1, 2.7, 3.0, 3.7, 4.6	15, 25, 35, 40, 45
2-hole Rasp	2.1, 2.7, 3.0, 3.7, 4.6	15, 25, 35, 40, 45
3-hole Rasp	2.1, 2.7, 3.0, 3.7, 4.6	15, 25, 35, 40, 45
Blunt Injector	1.4, 1.6, 2.1	5, 8, 10, 15
Sharp Injector	1.4, 1.6, 2.1	5, 8, 10, 15
Cobra Origional	2.1, 2.7, 3.0, 3.7, 4.6	15, 25, 35, 40, 45

Lipo Suction

Tips	Diameter (mm)	Length (cm)
Toomey Infiltrator	3.0, 3.7	15, 25, 35
Cobra Bi-Bevel	2.1, 2.7, 3.0, 3.7, 4.6	15, 25, 35, 40, 45
Mercedes	2.7, 3.0, 3.7, 4.6	15, 25, 35, 40, 45
Pyramid	2.1, 2.7, 3.0, 3.7, 4.6	15, 25, 35, 40, 45
Standard	2.1, 2.7, 3.0, 3.7, 4.6	15, 25, 35, 40, 45
2-hole Rasp	2.1, 2.7, 3.0, 3.7, 4.6	15, 25, 35, 40, 45
3-hole Rasp	2.1, 2.7, 3.0, 3.7, 4.6	15, 25, 35, 40, 45
Blunt Injector	1.4, 1.6, 2.1	5, 8, 10, 15
Sharp Injector	1.4, 1.6, 2.1	5, 8, 10, 15
Cobra Origional	2.1, 2.7, 3.0, 3.7, 4.6	15, 25, 35, 40, 45

Non – Disposable Needles

Initial Puncture Needles

Gauge	Length
18G	1 ½" To 1"
19G	1 ½" To 1"
20G	1 ½" To 1"
21G	1 ½" To 1"
22G	1 ½" To 1"
23G	1 ½" To 1"
24G	1 ½" To 1"
26G	1 ½" To 1"
27G	1 ½" To 1"
30G	1 ½" To 1"

Non – Disposable Needles

Initial Puncture Needles

Gauge	Length
18G	1 ½" To 1"
19G	1 ½" To 1"
20G	1 ½" To 1"
21G	1 ½" To 1"
22G	1 ½" To 1"
23G	1 ½" To 1"
24G	1 ½" To 1"
26G	1 ½" To 1"
27G	1 ½" To 1"
30G	1 ½" To 1"

Micro Suction Tubes

Angled cannula
Luer conical connection plug
Rounded cannula point
Cannulas can be used for dissection of soft issue

Available Sizes :

Gauge	Diameter	Length
14G	2.10mm	70mm
17G	1.47mm	60mm
19G	1.05mm	60mm
22G	0.70mm	60mm
27G	0.40mm	60mm

Angled cannula
Luer conical connection plug
Rounded cannula point
Cannulas can be used for dissection of soft issue

Available Sizes :

Gauge	Diameter	Length
14G	2.10mm	70mm
17G	1.47mm	60mm
19G	1.05mm	60mm
22G	0.70mm	60mm
27G	0.40mm	60mm

Pencil Point Spinal Needles

OEM manufacture according to your specifications and in your specified material

Gauge	Length (MM)
18G	3 ½"
19G	3 ½"
20G	3 ½"
21G	3 ½"
22G	3 ½"
23G	3 ½"
24G	3 ½"
25G	3 ½"
26G	3 ½"
27G	3 ½"

Pencil Point Spinal Needles

OEM manufacture according to your specifications and in your specified material

Gauge	Length (MM)
18G	3 ½"
19G	3 ½"
20G	3 ½"
21G	3 ½"
22G	3 ½"
23G	3 ½"
24G	3 ½"
25G	3 ½"
26G	3 ½"
27G	3 ½"

Spinal Needles (Transparent Hub)

Arrangement of Stylet & Cannula Hubs provides better bevel orientation
Transparent window hubs for contact clarity that helps better visualization
Fitted stylet reduces tissue trauma

Gauge	Length (MM)
18G	3 ½"
19G	3 ½"
20G	3 ½"
21G	3 ½"
22G	3 ½"
23G	3 ½"
24G	3 ½"
25G	3 ½"

Arrangement of Stylet & Cannula Hubs provides better bevel orientation
Transparent window hubs for contact clarity that helps better visualization
Fitted stylet reduces tissue trauma

Gauge	Length (MM)
18G	3 ½"
19G	3 ½"
20G	3 ½"
21G	3 ½"
22G	3 ½"
23G	3 ½"
24G	3 ½"
25G	3 ½"

Redon Needles

These High Quality Trocars with extremely sharp bevel for minimal trauma (causing less damage of the tissue) during insertion and bendable to meet operational requirements are available in stock.

Knife Tip

Trihedhon Tip

Flat Tip

Curved Tip Point

Curved Flat Point

Knife Tip

Trihedhon Tip

Flat Tip

Curved Tip Point

Curved Flat Point

Surface Grinding

Surface grinding is a precision machining process that involves the removal of material from the surface of a workpiece using an abrasive wheel. This process is widely used to achieve flat surfaces with high dimensional accuracy and a smooth finish. Surface grinding is commonly employed for finishing or preparing metal, plastic, and other materials for further manufacturing or assembly. Surface grinding is usually used for finishing flat surfaces, creating smooth and precise mating surfaces for parts, and removing material to achieve specific thickness or flatness requirements.

3D Printing

3D Printing is also known as additive manufacturing and involves creating three-dimensional objects layer by layer from a digital mold. The steps required in 3D Molding include:

Digital Model – a digital 3D model of the object must first be created.
Slicing – the digital model is sliced into numerous layers through specific software.
Printing – the 3D printer interprets these sliced layers and begins building the object layer by layer.
Layer Fusion – as each layer is deposited or solidified, it fuses with the previous layer and is repeated until the entire object is complete.
Post-Processing – Once the printing finishes, some objects require post-processing steps such as cleaning or curing.

Prototyping

Prototyping is a crucial phase in the product development process where a preliminary vision of a product is created to test and evaluate its design, functionality, and performance. The primary purpose of prototyping is to gather feedback, identify potential issues, and refine the product before moving forward with full-scale production. Prototypes can take different forms such as physical models or digital simulations based on the nature of the product. Prototyping is an essential step among teams to validate ideas, gather feedback, and refine designs before committing to full-scale production.

Product Engineering

Product engineering is the process of designing, developing, and bringing a new product to the market. It involves the application of engineering principles and practices to create products that meet specific requirements and address the needs of users or the market. Product engineering encompasses a range of activities from conceptualization to production and often involves collaboration among various engineering disciplines such as mechanical, electrical, software, and industrial engineering. The goal of product engineering is to create products that are innovative, reliable, and economically viable.

EtO Sterilization

EtO Sterilization or Ethylene Oxide Sterilization is a widely used method for sterilizing medical devices and other heat-sensitive items that cannot be sterilized by traditional methods such as steam or autoclaving. EtO is a colorless gas with strong sterilizing properties, and it is effective in destroying microorganisms, including bacteria, viruses, and spores. The main steps of EtO sterilization include preconditioning, gas exposure, the sterilization phase, aeration/ventilation, and then monitoring/quality assurance.

Process Validation

Process validation in manufacturing refers to the systematic and documented approach to ensuring that the manufacturing process consistently produces a product that meets predetermined specifications and quality standards. It is a critical component of quality assurance and regulatory compliance. The goal or process validation is to demonstrate that a manufacturing process is capable of consistently producing products that meet the intended quality attributes. Process validation is essential for industries where product quality and consistency are critical such as the medical industry.

Silk Screening (Screen Printing)

– Silk screening is a direct printing process which involves creating a stencil (screen) and then using it to apply ink directly onto the target surface. Silk screening is widely used for creating customized and high-quality prints on a diverse range of products.

Pad Printing

Pad printing is an indirect offset printing process which involves transferring an image from a printing plate to a silicone pad, which then transfers the image onto the target surface. Pad printing is widely used for creating customized and high-quality prints on a diverse range of products.

Complete Sewing

Complete sewing typically refers to the entire process of sewing a garment or textile item from start to finish. This involves various steps, including pattern making, cutting fabric pieces, assembling these pieces, and completing the finishing touches. This process is integral to the creation of clothing, home textiles, accessories, and other sewn items.

Complete Assembly

Complete assembly refers to the finished product that results from combining various components or parts into a single, functional unit. Assembly involves joining, fastening, or integrating individual parts to create a fully operational item. Some key aspects of the assembly process include component parts, the assembly process, an assembly line, quality control, subassemblies, integrating systems, and the final testing and inspection, packaging, and shipping.

Shoney Scientific Inc. is capable of complete assembly for any product made of plastic, metal, rubber, or fabric, and can customize the assembly line for your specific needs.

Form, Fill, and Seal (FFS)

Form, fill, and seal is a packaging process commonly used to automate the production of pre-formed bags or pouches, filling them with a product, and then sealing them. This integrated process is efficient, allowing for high-speed and continuous packaging of various products. The advantages of this process include efficiency, flexibility, reduced labor requirements, and consistent packaging. These machines come in different configurations to accommodate different packaging needs.

Complete Packaging Services

Packaging refers to the process of enclosing a product or item in protective material for the purpose of storage, transportation, display, and marketing. Packaging serves multiple functions, ranging from protecting the product from damage and contamination to conveying information about the product and promoting its brand. It is a critical aspect of the overall supply chain and plays a key role in the customer experience. Packaging materials vary widely and can include cardboard boxes, plastic containers, glass bottles, metal cans, flexible pouches, and much more.

Shoney Scientific Inc. can provide a wider range of high-quality and customized packaging based on your specific requirements.

Nonwoven Fabric Processing

Nonwoven fabric processing involves production of textiles without traditional sewing or knitting. Instead, nonwoven fabrics are manufactured by bonding or interlocking fibers using various methods. These fabrics are widely used in diverse applications due to their versatility, cost-effectiveness, and specific characteristics. The common methods include web formation, needle punching, spun bonding, melt blowing, spun lacing, and hydroentanglement.

Bonding

– Bonding refers to the process of joining two or more materials together to form a strong, cohesive connection. Various methods and techniques are used for bonding in different industries, and the choice of bonding method depends on factors such as the types of materials being joined, the intended application, and the desired properties of the bond. Some common types of bonding include adhesive bonding, welding, soldering, brazing, mechanical fastening, intermolecular bonding, hybrid bonding, and biological bonding. The choice of method depends on specific requirements such as the materials involved, strength, durability, and conductivity.

Titanium Coating

Titanium Coating, also known as Titanium Nitride Coating (TiN) is a thin film coating applied to various surfaces to enhance their performance and appearance. This coating is composed of titanium nitride, a hard ceramic material known for its excellent wear resistance, corrosion resistance, and decorative properties. Titanium Coating is applied through a process called physical vapor deposition (PVD) or chemical vapor deposition (CVD). Titanium coating increases wear and corrosion resistance, friction reduction, and increases aesthetic appeal. Titanium coating is used for medical applications, cutting tools, firearms, sporting goods, and electronics.

Stamping

Stamping, for manufacturing, refers to a metalworking process that involves cutting, shaping, or forming metal sheets or coils using a tool and die set. The process is known as “sheet metal stamping” or simply “metal stamping”. It is a cost-effective and efficient method for producing large quantities of parts with consistent shapes and dimensions.

Laser Marking

– Laser Marking is a non-contact marking process that uses a laser beam to create markings on the surface of a material. This method is widely used for labeling, branding, and adding identification or traceability information to various objects. Laser marking offers high precision, speed, and versatility, making It suitable for a wide range of materials and industries. Laser marking is an efficient method for adding marks to products, and is often favored due to it’s speed, precision, and adaptability to different materials and applications.

Chemical Polishing

Chemical polishing can be done in two ways, which are chemical mechanical polishing and acid polishing.

Chemical Mechanical Polishing is a process that combines chemical and mechanical actions and is commonly used in the semi-conductor industry. In this process, a slurry which contains abrasive particles and chemical agents is applied to the surface, and a polishing pad mechanically removes material while the chemical agents enhance the polishing action.

Acid polishing is a type of polishing that involves the use of an acidic solution to selectively dissolve material from the surface of a metal. This method can be applied to achieve a smooth and polished finish, but it may be less controlled than electropolishing.

Electrochemical Polishing

Electrochemical polishing is a process that selectively removes material from a metal surface. The metal part to be polished is immersed in an electrolyte solution, and an electric current is applied. The process smoothens the surface by preferentially dissolving microscopic peaks, resulting in improved surface finish, reduced micro-roughness, and enhance corrosion resistance. Electropolishing is often used for stainless steel and other metals.

Chemical Etching

Chemical etching also known as chemical milling or photochemical machining, is a subtractive manufacturing process used to selectively remove material from the surface of a substrate using chemical reactions. This process is particularly effective for producing intricate and precise metal parts with fine details and complex shapes. Chemical etching is commonly used in the production of precision parts for industries such as electronics, aerospace, and medical devices. Chemical etching offers a level of precision and detail that may be challenging or expensive with other methods.

Plating

Plating, in the context of manufacturing and metalworking, refers to the process of depositing a thin layer of metal onto the surface of another object. This is done for various reasons, including improving the object’s appearance, enhancing corrosion resistance, providing wear resistance, and facilitating soldering or brazing. The choice of plating and type of metal used depends on the specific requirements of the application.

Powder Coating

Powder Coating is a finishing process used to apply a durable and protective layer of color to a metal surface. In this process, a dry powder is electrostatically applied to the metal object. The coated object is then heated, causing the powder to melt and form a smooth, even, and durable coating as it solidifies. Powder coating provides a decorative finish and offers protection against corrosion, UV rays, and other environmental factors. It is widely used in various industries for coating metal products like appliances, automotive parts, and furniture.

Swaging

Swaging is a metalworking process that involves the reduction or shaping of a metal object by forcing it through a die or by compressing it with dies under high pressure. This process is commonly used to reduce the diameter of tubes, create tapered shapes, or form intricate details on the surface of metal components. Swaging is often used in the production of items like bullets, pipes, and certain types of fittings.

Centerless Grinding

Centerless grinding is a machining process used to remove material from the outside diameter of cylindrical workpieces without the need for a center, which is the central axis typically found on traditional cylindrical grinding. This process is well-suited for the precision grinding of small to medium-sized parts with high production volumes. Centerless grinding is commonly used in the production of cylindrical parts such as shafts, bolts, and rollers where precision and efficiency are crucial.

Pipe Bending

Pipe bending is a process that involves the deformation of a pipe or tube to achieve a desired shape. The goal is to bend the pipe without causing any damage to its structural integrity, maintaining the continuity of the material along the curve. Pipe bending is a versatile process, and the choice of method depends on the specific requirements of the application. It allows manufacturers to create pipes with customized shapes, ensuring they fit seamlessly into the overall design of a system or structure.

Sandblasting

Sandblasting, which is also knows as abrasive blasting is a process in which a stream of abrasive material is propelled at high speed against a surface to remove contaminants, shape the surface, or achieve a desired finish. The abrasive material, typically sand or other abrasive particles, is propelled using compressed air or a pressurized liquid. Sandblasting is widely used for cleaning, surface preparation, and finishing. Sandblasting is a versatile process used for tasks such as removing corrosion from metal surfaces, preparing surfaces for painting, cleaning industrial equipment, and creating decorative finishes on glass or metal.

Mold/Tool Building

Mold/tool building refers to the process of designing, creating, and constructing molds or tools used in manufacturing to produce specific components or products. These molds or tools are instrumental in shaping raw materials, such as plastic, metal, or rubber, into the desired forms. The quality, precision, and efficiency of the molds or tools significantly impact the final product’s characteristics and production process. Mold/tool building is a critical aspect of various manufacturing industries, including injection molding, die casting, and stamping.

Machining

Machining is a subtractive manufacturing process used to shape and finish metal products by removing material from a workpiece through various cutting and deformation methods. This process is employed to achieve precise dimensions, tight tolerances, and specific surface finishes in the production of metal parts and components. Some key methods of machining include turning, milling, drilling, grinding, machining centers, and electrical discharge machining (EDM). Machining can be used for both prototype development and high-volume production.

Formulating

In manufacturing, formulating applies to creating specific blends of raw materials to produce products with predefined characteristics. This is common in the formulation of polymers, plastics, and other materials based on requirements of the product.

Compounding

Compounding, in the context of manufacturing and materials, refers to the process of combining different raw materials or ingredients to create a new material with specific properties. The process is commonly used in various industries, including plastics, rubber, pharmaceuticals, and food processing. The goal of compounding is to achieve a material or product with specific characteristics that may not be present in individual raw materials alone and allows manufacturers to tailor their material.

LSR Molding

LSR Molding stands for Liquid Silicone Rubber molding which is a specialized process used to produce silicone rubber parts and components. Liquid silicone rubber is a high-purity platinum-cured silicone material that offers various benefits including flexibility, resistance, and biocompatibility. LSR molding is particularly suitable for applications where precision, durability, and the unique properties of silicone are crucial. LSR is commonly used in industries such as healthcare, automotive, electronics, and consumer goods where the unique properties of silicone rubber are advantageous.

Transfer Molding

Transfer molding is a manufacturing process designed for shaping rubber and elastomeric materials into intricate and high-precision products. This method seamlessly combines the advantages of compression molding and injection molding and offers a unique set of benefits. Transfer molding is used because of its precision in achieving intricate shapes and designs, uniformity in product dimensions and properties, efficiency, and versatility for diverse applications.

Compression Molding

Compression Molding is a widely used manufacturing process for shaping rubber and other elastomers into various products. It involves the use of heat and pressure to mold and cure rubber compounds and create objects with specific shapes and properties. Compression molding is particularly suitable for producing medium to large volumes of rubber products with consistent quality. Compression Molding is cost-effective, versatile as it can accommodate a wide range of rubber formulations and provides consistent and reliable results.

Punching

In the context of plastic products, punching refers to a process involving the use of a punch and die to cut or shape materials, typically plastic sheets, or films. This method is commonly known as die-cutting or punching and is a versatile technique employed to create precise and intricate shapes in plastics. A punch is a tool that cuts through the material and a die provides the shape or contour.

Punching is often used in the production of various plastic items, including packaging materials, gaskets, labels, and other precision components.

Surface Coating

Surface Coating is a process used to enhance the aesthetics, durability, and performance of a product. We have several types of coatings available, and we would love to go over your product and determine the best coatings that fit your project requirements.

Tipping

Tipping is a specialized process where a specific component, often a tip or cap is added to a product to improve functionality, aesthetics, or safety features of the product. The process involves carefully attaching or incorporating the tipping component on the main structure of the product. This process requires precision and attention to detail.

RF Welding

RF (Radio Frequency) welding is a sophisticated plastic joining technique that is used to create strong and durable bonds in thermoplastic material. In RF welding two pieces of plastic are placed between electrodes where a RF generator emits high-frequency electromagnetic energy. This will cause the molecules in the plastic to vibrate, which generates heat. The heated plastic softens and fuses, creating a seamless and robust bond when pressure is applied. RF Welding is well-suited for creating airtight and watertight seals making it perfect for inflatable products, medical bags, and automotive components.

Dip Molding

Dip Molding is a specialized plastic manufacturing process that is ideal for creating seamless, thin-walled, and flexible plastic products. A metal mold is immersed into a liquid polymer, such as PVC, latex, or plastisol. The mold is then gradually withdrawn, and the liquid coating adheres to the surface. Once the coated mold is exposed to heat, the polymer undergoes curing, which forms the solid and resilient layer that takes the shape of the mold. This process is used to produce uniform, high-quality, and customizable products, especially for grips, caps, handles, and medical devices.

Blow Molding

Blow molding is a sophisticated manufacturing process widely used to produce hollow plastic products, ranging from bottles and containers to automotive components. This method involves shaping molten plastic into a hollow form by blowing air into a mold. The plastic material then takes the shape of the mold as it expands, creating a seamless and lightweight final product. This procedure allows for efficiency in producing high volumes of consistent, durable, and cost-effective plastic containers.

Thermoforming

Thermoforming is a versatile manufacturing process employed to shape plastic sheets into a wide range of products. The process involves heating a plastic sheet until it becomes pliable, then forming it into a specific shape using a mold or pattern. Once the plastic cools and solidifies, the desired product is obtained. This method is cost-effective and allows for rapid production capabilities and intricate designs.

Extrusion

Extrusion is a manufacturing process used to create plastic parts made of consistent cross-sectional profiles. Plastic material is melted and forced through a die to produce a continuous shape, such as tubing, pipes, or other items. Once the material is cooled, the product is cut to its desired lengths. Extrusion is a process that is cost-effective and offers the ability to produce lengthy components with uniformity.

Injection Molding

Injection Molding is a highly versatile manufacturing process used to produce intricate and precise plastic components. In this process, molten plastic is injected into a mold cavity, where it cools and solidifies to form the desired shape. Injection molding is a cost-effective solution for the mass production of a diverse range of plastic products.

Male External Catheter – SURUXCATH ®

Male External Catheter - SURUXCATH ®

Item Code

2028

Features :

> Penile sheath / external catheter
> Male catheter is specially designed for urine incontinence for day and night use in male patient
> Manufactured from pure latex for soft and gentle feel
> Proximal end is designed for easy connection to urine bag / leg bag, making it simple to use
> Provided with self adhesive coated strip for proper fixing on to the penis
> Sterile product for single use

Size Available in	Small	Medium	Large	Extra Large
MM	20	25	30	35

Female Catheter

Item Code

2028

Features :

> Soft, frosted and kink resistant PVC tubing
> Proximal end is fitted with universal funnel shaped connector for safe connection to urine bag
> Catheters are manufactured from non toxic, non irritant, soft PVC compatible with catheter lubricants
> Available with the option of radio-opaque line throughout the length for X ray visualization
> Atraumatic, soft, rounded, closed tip with two lateral eyes for efficient drainage
> Colour coded plain connector for easy identification of size
> For short term bladder catheterization through urethra in females
> Sterile product for single use

Available Configuration :

Length : 18 cm

Size in FG	6	8	10	12	14	16	18	20
Color	Light Green	Blue	Black	White	Green	Orange	Red	Yellow

Nelaton Catheter

Item Code

2018

Features :

> Soft, frosted and kink resistant PVC tubing
> Proximal end is fitted with universal funnel shaped connector for safe connection to urine bag
> Catheters are manufactured from non toxic, non irritant, soft PVC compatible with catheter lubricants
> Available with the option of radio-opaque line throughout the length for X-ray visualization
> Atraumatic, soft, rounded, closed tip with two lateral eyes for efficient drainage
> Colour coded plain connector for easy identification of size
> For short term bladder catheterization through urethra in males
> Sterile product for single use

Available Configuration :

Also available with DEHP free tube
Length : 40 cm

Size in FG	6	8	10	12	14	16	18	20	22	24
Color	Light Green	Blue	Black	White	Green	Orange	Red	Yellow	Violet	Light Blue

Foley Balloon Catheter (Latex) SURUCATH ®

Item Code

2006

Features :

> Latex, siliconised coating
> Smooth tapered tip of catheters facilitates easy introducing into the urethra
> The drainage eyes are accurately formed to permit effective drainage
> The symmetrical balloon expands equally in all directions so as to perform its function of retaining bladder efficiently
> The smooth outer surface is specially treated with medical grade silicon fluid which facilitates easy passage through urethra
> Colour Coded sleeves are useful for easy and rapid size identification
> Plastic valve permits simple use of all commonly used type of syringe nozzles for easy inflation/ deflation and are proved to be more efficient than rubber valves
> Sterile product for single use

Available Configuration :

Available with plastic value
Type : Two way and Three way
Also available Female Catheter with length 22 cm

Balloon Capacity (ml/cc)	Two Way Sizes (FR)	Three Way Sizes (FR)
1-5	6	–
3-5	8, 10	–
5-15	12, 14, 16, 18, 20, 22	–
30	16, 18, 20, 22, 24	–
30-50	16, 18, 20, 22, 24	16, 18, 20, 22, 24

All Silicon Foley Balloon Catheter

Item Code

2007

Features :

> 100 % silicon construction
> Medium length round tip with two opposing eyes
> With radio-opaque line
> Maximum softness and bio-compatibility to enhance patient comfort
> Technically advanced process makes the balloon an integral part of the tip
> No “glue” ridge to irritate the urethral upon insertion and removal
> Remarkably smooth, the non stick surface of silicon makes it highly resistant to encrustation
> The shaft allows for an approximately 30 % larger lumen, which can permit longer use and promotes better drainage of sediment and blood clots
> The ribbed funnel ensures an easy, leak proof connection while the clear connector and clear shaft allows visual examination of drainage
> Sterile product for single use

Balloon Capacity (ml/cc)	Two Way Sizes (FR)	Three Way Sizes (FR)
3	-	–
3-5	8, 10	–
5-10	12, 14, 16, 18, 20, 22, 24, 26	16,18, 20, 22, 24
5-15	12, 14, 16, 18, 20, 22, 24, 26	16,18, 20, 22, 24
30	16,18, 20, 22, 24, 26	16, 18, 20, 22, 24

Urine Collection Bag (With Measured Volume Meter)

Item Code

3015M

Features :

> Graduated in ml with measured volume meter for accurate measurement of urine
> Conical inlet connector with cap
> Closed circuit system eliminates the risk of contamination
> Soft and kink resistant PVC tubing
> Urine Collection Bag capacity : 2000 ml

Available Configuration :

Inlet tube length : 90 and 100 cm
Capacity of volume meter : 250 ml, 500 ml

Paediatric Urine Bag – SURU-BABY BAG

Paediatric Urine Bag - SURU-BABY BAG

Item Code

3015P

Features :

> Provided with special adhesive for better grip and easy removal from soft skin of the infant
> For short term urine collection
> Suitable for both male and female infants
> Sterile product for single use
> Capacity : 100 mL

Urine Collection Bag
(With Bottom Outlet)

Item Code

3015

Features :

> For short and long term urine collection
> For clean single hand operation and efficient emptying of the bag
> Bag graduated in ml to indicate the quantity of urine collected
> Conical inlet connector with cap
> With non-return valve
> Sterile product for single use

Available Configuration :

Also available with / without sampling port
Capacity : 2000 ml

Urine Collection Bag
(Leg Bag with Bottom Outlet)

Item Code

3015 L

Features :

> For short and long term urine collection
> Provides freedom of mobility as the bag is attached to the leg of the patient
> Available with leg straps
> Bag graduated in ml to indicate the quantity of urine collected
> Soft and kink resistant PVC tubing With non return valve
> Conical inlet connector with cap

Available Configuration :

Capacity : 800 ml
Tube length : 50 cm ± 5 cm

Urine Collection Bag (With Hanger)

Item Code

3015H

Features :

> For short and long term urine collection
> For clean single hand operation and efficient emptying of the bag
> Specially molded handle for easy handling
> Soft and kink resistant PVC tubing
> Bag graduated in ml to indicate the quantity of urine collected
> Sterile product for single use
> Capacity : 2000 ml

Available Configuration :

Tube length : 90 & 100 cm

Percutaneous Nephrostomy
Drainage Set (Pigtail)

Item Code

4071

Features :

> Catheter made up of specially formulated and biocompatible Polyurethane material, which provides strength during insertion for longevity and also softens at body temperature to conform to the body tissues and reduces the risk of vascular trauma
> Catheter is highly radiopaque for better visualization.
> Eyelets on catheter are non-traumatic
> The Pigtail tip & J shape configuration helps in the retention of the distal tip in the renal pelvis.
> PTFE Coated flexible guidewire with “J” Tip

Available Configuration :

Size : FR 8 to 16
Length : 22 to 30 cm

Percutaneous Nephrostomy Drainage Set

Item Code

4066

Features :

> Catheter made up of specially formulated and biocompatible Polyurethane material, which provides strength during insertion for longevity and also softens at body temperature to conform to the body tissues and reduces the risk of vascular trauma
> Catheter is highly radiopaque for better visualization.
> Eyelets on catheter are non-traumatic
> The Malecot flower design is ideally suited for enhanced drainage & promotes catheter retention
> PTFE Coated flexible guidewire with “J” Tip

Available Configuration :

Size : FR 8 to 16
Length : 22 – 30 cm

Reusable LipoFil™ Cannula Style I Mini with Obturator

A 19 gauge needle with obturator for clearing clogged lumen. Blunt tipped as in all Style I, used in areas where nerves, vessels or glands may be an issue. A short length and narrow gauge allows maximum control for use around the eyes or other areas where control is important.

Catalog Number	OD	Length
LS-DI3-R	19g	3cm
LS-D16-R	19g	6cm

Reusable LipoFil™ Cannula Style II

The most commonly used re-injection cannula. Partially open tip passes through most tissue types, and its blunt design minimizes damage to underlying structure. It can be used around the lips, the malar eminence, cheeks, and other areas that do not require placement of tissue directly under the skin or in fibrous dense areas. The Concave design allows navigation around soft tissue structures and for special placement. Useful for enhancing the dorsum of the nose via the forehead, and through the glabella or nasion.

Catalog Number	OD	Length
LS-DII7-R	16g	7cm
LS-DII9-R	16g	9cm
LS-DII9-R 9 (Curved)	16g	9cm

Reusable Luer to Luer Connector

Catalog Number	OD	Length
BE-LL3-R	N/A	N/A

Reusable LipoFil™ “w” Dissector for Face & Body

Catalog Number	OD	Length
LS-DW9-R	3mm	9cm
LS-DW15-R	3mm	15cm

Reusable LipoFil™ Aspiration Cannula

The Aspiration cannulas are used for harvesting tissue for re-injection. The special tip design with its blunt, yet open, style allows the harvested tissue parcel to flow through the standard Style I, II, or III tip design cannulas.

Catalog Number	OD	Length
LS-DASP15-R	3mm	15cm
LS-DASP23-R	3mm	23cm
LS-DASP23-R (Curved)	3mm	23cm

Reusable LipoFil™ Body Cannula

A Style I tip design for general aspiration when performing soft tissue removal procedures. It can be used for harvesting tissue for reinjection in areas where large volume placement is required.

Catalog Number	OD	Length
LS-DB1215-R	12g	15cm
LS-DB1223-R	12g	23cm
LS-DB1415-R	14g	15cm
LS-DB1423-R	14g	23cm

Reusable LipoFil™ Hood Cannula

The Hood tip cannula is used for re-injection of large tissue volumes. Its “hooded” design enables safe injection into the breast for augmenting and around breast implants for post-operative refinement including: disguising edges or rippling of existing implants, desguise breast implants that do not look natural, sculpt and shape the breast.

Catalog Number	OD	Length
LS-DH1015-R	10g	15cm
LS-DH1015-R	10g	23cm
LS-DH1215-R	12g	15cm
LS-DH1223-R	12g	23cm

Reusable LipoFil™ Cannula Style III Mini with Obturator

A 19 gauge needle with obturator for clearing clogged lumen. The flat, spatulated tip provides maximum control and an easy advance to enhance the areas around the eye, especially directly beneath the skin in the lower eyelid, the lateral border of the eye, and around the lips and mouth. It is recommended for areas where it may be difficult to advance in fibrous tissues.

Catalog Number	OD	Length
LS-DIII3-R	19g	3cm
LS-DIII6-R	19g	6cm

Reusable LipoFil™ Cannula Style III

Open tip design that provides for maximum control as the cannula is advanced through dense or fibrous tissue. Can be used to place tissue under the skin or next to the mucosa when injecting in or around the lips. The flat, spatulated tip aids in enhancing the border of the lips, the lower eye-lid and around the eye. Additionally, the Concave design allows the surgeon to navigate soft tissue areas and assists in special placement.

Catalog Number	OD	Length
LS-DIII7-R	16g	7cm
LS-DIII9-R	16g	9cm
LS-DIII9-R (Curved)	16g	9cm

Reusable LipoFil™ Cannula Style I

Catalog Number	OD	Length
LS-DI7-R	16g	7cm
LS-DI9-R	16g	9cm

Reusable LipoFil™ 32 Series Aspiration Cannula

Catalog Number	OD	Length
LS-32ASP215-R	2mm	15cm
LS-32ASP315-R	3mm	15cm

Reusable LipoFil™ O Series Mini Cannula with Obturator

Catalog Number	OD	Length
LS-DOO169-R	16g	9cm
LS-DOO197-R	19g	7cm

Mercedes Cannula

Catalog Number	OD	Length
BE-MER310LL (Luer Lock)	3mm	10cm
BE-MER315B (Handle)	3mm	15cm
BE-MER315LL (Luer Lock)	3mm	15cm
BE-MER315S (Handle)	3mm	15cm
BE-MER323LL (Luer Lock)	3mm	23cm
BE-MER325LL (Luer Lock)	3mm	25cm
BE-MER326S (Handle)	3mm	26cm
BE-MER332S (Handle)	3mm	32cm
BE-MER415S (Handle)	4mm	15cm
BE-MER426B (Handle)	4mm	26cm
BE-MER432B (Handle)	4mm	32cm
BE-MER525B (Handle)	5mm	25cm
BE-MER526B (Handle)	5mm	26cm
BE-MER532B (Handle)	5mm	32cm
BE-MER536B (Handle)	5mm	36cm

Standard Cannula

Catalog Number	OD	Length
BE-STD215LL (Luer Lock)	2mm	15cm
BE-STD215S (Handle)	2mm	15cm
BE-STD223LL (Luer Lock)	2mm	23cm
BE-STD223S (Handle)	2mm	23cm
BE-STD315LL (Luer Lock)	3mm	15cm
BE-STD315S (Handle)	3mm	15cm
BE-STD323LL (Luer Lock)	3mm	23cm
BE-STD326S (Handle)	3mm	26cm
BE-STD332S (Handle)	3mm	32cm
BE-STD415S (Handle)	4mm	15cm
BE-STD426B (Handle)	4mm	26cm
BE-STD432S (Handle)	4mm	32cm

Becon III Cannula

Catalog Number	OD	Length
BE-III310LL (Luer Lock)	3mm	10cm
BE-III315LL (Luer Lock)	3mm	15cm
BE-III315S (Handle)	3mm	12cm
BE-III323LL (Luer Lock)	3mm	23cm
BE-III326S (Handle)	3mm	26cm
BE-III332B (Handle)	3mm	32cm
BE-III332S (Handle)	3mm	32cm
BE-III336B (Handle)	3mm	36cm
BE-III415S (Handle)	4mm	15cm
BE-III426B (Handle)	4mm	26cm
BE-III432B (Handle)	4mm	32cm
BE-III526B (Handle)	5mm	26cm
BE-III532B (Handle)	5mm	32cm

Spatula Cannula

Catalog Number	OD	Length
BE-SPA315LL (Luer Lock)	3mm	15cm
BE-SPA315S (Handle)	3mm	15cm
BE-SPA415B (Handle)	4mm	15cm
BE-SPA415S (Handle)	4mm	15cm
BE-SPA426B (Handle)	4mm	26cm
BE-SPA515B (Handle)	5mm	15cm
BE-SPA515S (Handle)	5mm	15cm
BE-SPA526B (Handle)	5mm	26cm

Spiral Cannula

Catalog Number	OD	Length
BE-SPI326S (Handle)	3mm	26cm
BE-SPI426B (Handle)	4mm	26cm
BE-SPI432B (Handle)	4mm	32cm
BE-SPI436B (Handle)	4mm	36cm
BE-SPI526B (Handle)	5mm	26cm
BE-SPI532B (Handle)	5mm	32cm

Becker Cannula

Catalog Number	OD	Length
BE-BEC310LL (Luer Lock)	3mm	10cm
BE-BEC315LL (Luer Lock)	3mm	15cm
BE-BEC315S (Handle)	3mm	15cm
BE-BEC323LL (Luer Lock)	3mm	23cm
BE-BEC326LL (Luer Lock)	3mm	26cm
BE-BEC326S (Handle)	3mm	26cm
BE-BEC426B (Handle)	4mm	26cm
BE-BEC426LL (Luer Lock)	4mm	26cm
BE-BEC432B (Handle)	4mm	32cm
BE-BEC440B (Handle)	4mm	40cm

Del Vecchio™ 32 Series Cannula

Catalog Number	OD	Length
BE-32DEL215LL (Luer Lock)	2mm	15cm
BE-32DEL315LL (Luer Lock)	3mm	15cm
BE-32DEL326S (Handle)	3mm	26cm
BE-32DEL332B (Handle)	3mm	32cm PTT
BE-32DEL332S (Handle)	3mm	32cm
BE-32DEL426B (Handle)	4mm	26cm
BE-32DEL430B (Handle)	4mm	30cm PTT
BE-32DEL432B (Handle)	4mm	32cm
BE-32DEL436B (Handle)	4mm	36cm
BE-32DEL526B (Handle)	5mm	26cm
BE-32DEL532B (Handle)	5mm	32cm

Del Vecchio™ 34 Series Cannula

Catalog Number	OD	Length
BE-34DEL322S-R-PTT (Handle)	3mm	22cm PTT
BE-34DEL326S-PTT (Handle)	3mm	26cm PTT
BE-34DEL330B-PTT (Handle)	3mm	26cm PTT
BE-34DEL332S-PTT (Handle)	3mm	32cm PTT
BE-34DEL336S-PTT (Handle)	3mm	36cm PTT
BE-34DEL422S-R-PTT (Handle)	4mm	22cm PTT
BE-34DEL426B-PTT (Handle)	4mm	26cm PTT
BE-34DEL430B-PTT (Handle)	4mm	30cm PTT
BE-34DEL432-PTT (Handle)	4mm	32cm PTT
BE-34DEL436B-PTT (Handle)	4mm	36cm PTT
BE-34DEL526B-PTT (Handle)	5mm	26cm PTT
BE-34DEL530B-PTT (Handle)	5mm	30cm PTT
BE-34DEL532B-PTT (Handle)	5mm	32cm PTT

Becker Twister Cannula

Catalog Number	OD	Length
BE-TWI0315BH-R (Reusable)	3mm	15cm
BE-TWI0326LL-R (Reusable. Luer Lock Handle)	3mm	26cm
BE-TWI0426LL-R (Reusable. Luer Lock Handle)	4mm	26cm
BE-TWI315LL (Luer Lock)	3mm	15cm
BE-TWI326S (Handle)	3mm	26cm
BE-TWI415B (Handle)	4mm	15cm
BE-TWI415LL (Luer Lock)	4mm	15cm
BE-TWI426B (Handle)	4mm	26cm

Sattler Cannula

R F Needle

Catalog Number	OD	Length
BE-SAT215LL (Luer Lock)	2mm	15cm
BE-SAT215S (Handle)	2mm	15cm
BE-SAT220LL (Luer Lock)	2mm	20cm
BE-SAT223LL (Luer Lock)	2mm	23cm
BE-SAT223S (Handle)	2mm	23cm
BE-SAT323LL (Luer Lock)	2mm	23cm
BE-SAT323S (Handle)	2mm	23cm

Schedule time with me

Catheter With Marking

OEM Manufacture according to your specification and in your specified material.

Torquer

Available sizes : Guide Wire from 0.30mm upto 0.90mm
OEM Manufacture according to your specifications and in your specified material

Plastic Components

Clean room moulding
Products are moulded from special grades of materials like Antistatic ABS, Carbon filled PC, PC/ABS, Polycarbonate, HIPS, Acrylic and various other materials.